[post_title]
Description:
MULTI-POSITION FURNACE INSTALLER'S INFORMATION MANUAL RTI F I CE E D D E SIGN burner orifices. 2. Gas supply pressure must be between 11 and 13 inches W.C. for propane (LP) gas. See Section 15, "Gas Supply Pressure and Pilot Adju stment."
Product Description of [post_title] below:
Domestic Shipping: This item is also available for shipping to select countries outside the U.S.
International Shipping: This item is not eligible for international shipping.
Average Customer Review: 9/10
The high altitude orifices should be changed by the following procedure: 1. manometer to furnace. 2. Turn on the gas supply and bleed air from the gas supply lines at a point as close to the inlet or the gas valve as is practical. WARNING:
TWO-STAGE, VARIABLE SPEED GAS-FIRED FURNACE PUB. NO. 12-1095-09 Freedom 80vs MODELS AUD2B060A9V3VB AUD2B080A9V3VB AUD2C080A9V4VB AUD2C080B9V4VA ORIFICES — Main Nat. Gas. Qty. — Drill Size L.P. Gas Qty. — Drill Size GAS VALVE PILOT SAFETY DEVICE Type BURNERS — Type Number
INSTALLATION INSTRUCTIONS NATURAL GAS to PROPANE GAS CONVERSION KIT Condensing and Non There are enough orifices in each kit for largest furnace. Discard extra orifices. NOTE: DO NOT reinstall the manifold at this time. INSTALL MIXER SCREWS
PROPANE HIGH ALTITUDE CONVERSION ACCESSORY MODEL 1HA0408 This accessory provides the parts to operate a propane gas furnace at elevations between 2,000 and 6,000 feet (610 and Install the appropriate propane gas pilot orifices from this kit. Reconnect and tighten pilot tubing at the pilots.
(#55 Orifices) TBD TBD TBD TBD PROPANE AND HIGH ALTITUDE KITS NOMINAL WIDTH FOR GAS FURNACE A: Fits 14" Furnace Cabinet B: Fits 17 1/2" Furnace Cabinet C: Fits 21" Furnace Cabinet Gas Supply Pressure (Natural/Propane) ("w.c.)
HIGH-EFFICIENCY DOWNFLOW / HORIZONTAL FURNACE INSTALLER'S INFORMATION MANUAL RT IF C E E D D E S I G N ATTENTION, INSTALLER! main burner orifices to obtain proper gas flow rate. 10. Shut off furnace. Turn off gas at equipment shut-off
The furnace. Pay attention to all safety warnings and any other special notes highlighted in the manual. Carefully remove the burner orifices from the gas manifold, as shown in Figure 1. 9. Remove the four fasteners that secure the burner box to the
Conversion instructions from natural gas to propane Install the new main gas orifices and copper gaskets. Check with Tab. 1 that the correct orifices for operation of the boiler are installed. 22. Screw bottom burner box panel into place again.
G50DF(X) Series GAS FURNACE 505,255M 10/2009 Supersedes 05/2009 unit input rate is incorrect, check gas orifices for proper size and restriction. 3 − Remove temporary gas meter if installed. NOTE − To obtain accurate reading, shut off all other gas
ORIFICES — Main Nat. Gas. Qty. — Drill Size L.P. Gas Qty. — Drill Size GAS VALVE PILOT SAFETY DEVICE Type BURNERS — Type Number POWER CONN. Service Facts – Gas Furnace – Induced Draft – Upflow / Horizontal and Downflow / Horizontal – Single Stage Heat Models AUD1, TUD1, ADD1, TDD1
LP Gas Kit (#56 Orifices) TBD PROPANE AND HIGH ALTITUDE KITS GCH90703BX** GCH90704CXA* GCH90904CXA* GCH90905DXA* GCH91155DXA* 16 19-1/2 23 17-1/2 21. 7 NOMINAL WIDTH FOR GAS FURNACE A: Fits 14" Furnace Cabinet B: Fits 17 1/2" Furnace Cabinet
Conversion Instructions—LP Gas to Natural Gas. 27. Disconnect burner supply tube, pilot tube and thermocouple from the thermostat and remove the entire burner assembly by rotating
Propane Orifice Size Chart.pdf DOWNLOAD HERE 1 / 2. A75 Orifices – Davies Supply Group Ltd. http://daviessg.com/uploads/catalog/a75_80_orfices.pdf convert a natural gas furnace to a propane (LP) gas app-
NAHA00801LP or PART NO. 1183388 INSTALLATION INSTRUCTIONS NATURAL TO PROPANE CONVERSION KIT furnace on propane gas.! CAUTION 13. For NOx device removal, follow these additional Check manifold orifices for gas leaks when main