Furnace Installation Check Sheet

By | November 23, 2015

[post_title]
$1184.00


Description:

Greenwood Furnace Installation Checklist Customer name: Greenwood model: Street address: Serial number: City/State/Zip: Installation date: Dealer: Installer name:

Product Description of [post_title] below:


Domestic Shipping: This item is also available for shipping to select countries outside the U.S.
International Shipping: This item is not eligible for international shipping.
Average Customer Review: 9/10

Heating & Air Conditioning Installation Bid Comparison Checklist Will you check for damage to existing ductwork and duct insulation, and make repairs if necessary? ENERGY STAR quality installation checklist Author: US EPA

Furnace to floor distance For regular systems only Leak check Y N Pickup Filter used Y N For Regular Systems only – using Furnace Installation & Startup Checklist. Electrical Components Measurement Specification

Can result from contact with sharp sheet metal edges. Be careful when you handle this equipment. multiple furnace installation may use a group of up to See Installation Instructions for details and DIP switch settings.

4—Way Multipoise Gas Furnace Installation, Start—up, Operating, and Service and Maintenance Instructions check for leakage at furnace prior to operating furnace. If pressure exceeds 0.5 psig – Green/Yellow wire MUST be connected to furnace sheet metal

Furnace Installation straps should be attached to the furnace bottom side with sheet metal screws and to the rafters or joists with bolts. The gas meter can be used to measure input to furnace. Check with gas supplier for actual BTU content. 1.

START–UP CHECK SHEET (Keep this page for future reference) Dealer Name: Address: Business Card Here City, State(Province), Zip or Postal Code: This furnace is NOT approved for installation in mo-bile homes, trailers or recreation vehicles.

A gas-fired furnace for installation in a residential garage must be Gas Furnace FIGURE 8: Combustible Floor Base Accessory FIGURE 9: Horizontal Application check for gas leakage around the gas valve pressure

FURNACE Installation on Combustible Flooring Figure 13 NOTE − A sheet metal screw may be used to secure the intake pipe to the connector, if desired. Use a drill 2 − Check for the correct voltage at the furnace (furnace operating).

Furnace Tune-Up Check List [ ] Check, adjust and clean blower components • Removing excess dirt buildup will insure proper airflow and system balance.

90+ GAS FURNACE INSTALLATION INSTRUCTIONS GAS FURNACE SAFETY Table of Contents GAS FURNACE SAFETY For natural gas, check the furnace rate by observing the gas meter, making sure all other gas appliances are turned off.

#_____ Check List for Furnace Inspection Ser. #_____ Safety Controls, Technical Data, and over-all operating Furnace Running 27.Check Ohms on electric eye to verify proper operation. Check Exhaust Pipe for Proper Installation

506501-01 Issue 1031 Page 1 of 48 *506501-01* This manual must be left with the homeowner for future reference. INSTALLATION INSTRUCTIONS A95UH, A93UH, 95G1UH & 92G1UH

ڤ Inspection Record card or summary permit sheet shall be ڤ Heating Equipment → Listed and installed per manufacturer installation instructions- provide instructions → Check for vibration isolation between duct and furnace on supply and return. → Check overall tightness

Page 4 of 39 Issue 1031 506526-01 A80UH & 80G1UH Gas Furnace The A80UH & 80G1UH gas furnace is shipped ready for installation in the upflow or horizontal right position (for

Result from contact with sharp sheet metal edges. Be careful when you handle this equipment. Improper installation of the furnace can result in personal injury or death. Check for the correct voltage at the furnace (furnace operating). 3. Check amp-draw on the blower motor.

4—Way Multipoise Gas Furnace Installation, Start—up, Operating, and Service and Maintenance Instructions check for leakage at furnace prior to operating furnace. If pressure exceeds 0.5 psig – Green/Yellow wire MUST be connected to furnace sheet metal

check your wiring configuration and make sure you are familiar Installation Sheet Conventional RH RH RC, R Y, Y1 Y G, F G W, W1 W W2 W2 Y2 Y2 C C A A Figure 3a. 3 Wire Hot Water with Damper Valve Thermostat Mounting Plate Wall RH RC Y G W W2 Y2 C A RH W A Jumper

See Also:
Return To Home Page - Click Here

More Search Results From Google

Leave a Reply

Your email address will not be published. Required fields are marked *