York Furnace Drain Trap

[post_title]

Description:

York Air Handling Units Operation and Maintenance 102.20-OM1 Steps to Protect New Equipment Warranty 102.20-CL1 FiguRe 38 – GAS FURNACE DRAIN TRAP. OhnsOn COntROls 49 SECTION 3 – HANDLING, STORAGE, AND INSTALLATION FORm 102.20-n3 issue dAte: 6/01/2015 3

INSTALLATION INSTRUCTIONS A95UH, A93UH, 95G1UH & 92G1UH condensate trap and drain connections, and installation and service clearances [24 inches (610 mm) at unit front]. The unit must be level from A multiple furnace installation may use a group of up to

P3ur (styles a, b, c, and d) upflow natural gas furnaces (90%) hvac service parts supersedes: 035-14338-001 rev. b (0303) 3 58 trap, condensate 028-13241-000 028-13241-000 028-13241-000 028-13241-000 inducer drain 028-12463-002 028-12463-002 028-12463-002 028-12463-002

Gf9s series (style g) 91% downflow/horizontal 1 7 control, furnace module 031-01972-000 031-01972-000 031-01972-000 * 8 fuse 025-32746-026 025-32746-026 025-32746-026 * 69 drain tube, condensate trap 028-13309-004 028-13309-004 028-13309-004

5005 York Drive Norman, OK 73069 *697933* Furnace is multi-position and may be installed in any of the configurations shown. Ensure that all PVC venting has at least 1/4” per foot slope towards Do not install an external condensate trap. When drain hose routing changes are required

Installation instructions. • A room thermostat is used to control the furnace. New York, NY 10018 National Fire Protection Association 1 Batterymarch Park drain into the furnace trap as long as there is a trap between the coil and

The installation of this heat tape kit on the furnace condensate drain trap must be per these instructions to prevent electrical and fire hazards. 1. Use a ground fault protection device (GFPD) to minimize the danger of fire if heat tape becomes

58MVB 4-Way Multipoise Variable-Capacity Condensing Gas Furnace Installation, Start-Up, tube is used to extend the condensate trap drain connection to the desired furnace side for field drain attachment. See Condensate Trap Tubing (Factory-Shipped Orientation)

Broadway New York, NY 10018 Location Considerations DRAIN TRAP w/ 3/4" PVC DISCHARGE (RIGHT OR LEFT SIDE) 2 C B FRONT VIEW A (DISCHARGE) 1 1/2 HIGH VOLTAGE NOMINAL WIDTH FOR GAS FURNACE A: Fits 14" Furnace Cabinet B: Fits 17 1/2" Furnace Cabinet

Gas Furnace FIGURE 8: Combustible Floor Base Accessory FIGURE 9: field-supplied trap prior to the furnace drain connection to prevent conditioned air leakage. All drain connections 5005 York Drive Norman, OK 73069. 364861-UIM-G-1211

For the replacement of Secondary Heat Exchanger tached to furnace. Use this secondary heat exchanger kit to replace a failed secondary heat exchanger. trap drain stub facing outwards and fasten the assemblytotheblowerdeckwiththescrewsre-

Institute, Inc., 11 West 42nd Street, New York, NY 10036. In Canada, installation Install drain trap using appropriate Route the condensate line to an open drain. Condensate line must maintain a 1/4” downward slope from the furnace to the drain. 5. If unit will be started

Furnace Type V:Variable Speed – 2 Stage Product Type G: Goodman Brand Supply Type Broadway New York, NY 10018 Location Considerations DRAIN TRAP w/ 3/4" PVC DISCHARGE (RIGHT OR LEFT SIDE) 3/4 40 3/4 2 1/16 2 BOTTOM KNOCK-OUT C B D FRONT VIEW

Coil must be installed upstream (discharge air) of the furnace. 2. For Horizontal Water coming from this line means the coil primary drain is plugged and needs clearing. A trap must be installed in the drain line below the bottom of the drain pan.

New York, NY 10018 National Fire Protection Association 1 Batterymarch Park Quincy, MA 02269 CSA International • The drain trap supplied with the furnace must be used. • The drain line between furnace and drain location must

MODELS AHI & AVI. 2 JOhNsON CONtROls FORM 115.24-NOM7 (908) allow the condensate from the coils to drain from the drain pan. See Fig. 4. Trap detail for negative cabinet static pressure York Product Technical Support Created Date:

5005 York Drive Norman, OK 73069 *697933* Furnace is multi-position and may be installed in any of the configurations shown. Ensure that all PVC venting has at least 1/4” per foot slope towards Do not install an external condensate trap. When drain hose routing changes are required

Visit us on the web at york.com Additional rating information can be found at ahridirectory.org • Patent pending self priming internal condensate trap design for easy installation. • Venting applications Condensate Drain (Downflow)